X-Authentication-Warning:	delorie.com: mail set sender to geda-user-bounces using -f
X-Recipient:	geda-user AT delorie DOT com
X-Original-DKIM-Signature:	v=1; a=rsa-sha256; c=relaxed/relaxed;
	d=gmail.com; s=20120113;
	h=mime-version:date:message-id:subject:from:to:content-type;
	bh=PJBZg3opgLyJjB07WZnavh8rs8Id25NXJSj0HSDhbNs=;
	b=i0MtvlchyAzDTe9Fohml9DMqwCmcCGsJzOmVWSJFTWFuLPfaqi1IP/E46QkEHj6fbC
	MPWtuO2LLS1peMi5V9Pm1LjDSxIq4UsZ7xs8+TL3qA+ioEGC8lArB9/9rHg0gwAiJzti
	yIHQgQkfDfFDfZ39fwE76ezBcBaj2IZZ19T8Mj4pfMktU2vcndTMnThG2l60ClQhrBKD
	/PS5XtMXQZCNUqGLIfLf8UxSITQliQPr8RQDP/MT+nEQZUl6MH5YJWyGppsWV3iSPVNH
	8MjC+JjP5coJ2wxG01TWc0YD9r1bqem3roxIR+MDhScBSHXbMDoDJPsCb9T28ZpIxn67
	JY1w==
MIME-Version:	1.0
X-Received:	by 10.112.126.69 with SMTP id mw5mr4830808lbb.111.1441393400111;
	Fri, 04 Sep 2015 12:03:20 -0700 (PDT)
Date:	Fri, 4 Sep 2015 13:03:20 -0600
Message-ID:	<CAFx0xxi7tMzwv_cN6pUcATz3vQLQ5ugkFcGegNLtCcQuJOxnsA@mail.gmail.com>
Subject:	[geda-user] clearances for auto-routed traces with copper pours
From:	"Dave Williams (dave DOT williams DOT lists AT gmail DOT com) [via geda-user AT delorie DOT com]" <geda-user AT delorie DOT com>
To:	geda-user AT delorie DOT com
Reply-To:	geda-user AT delorie DOT com

--001a11c3781a98692e051ef08da6
Content-Type: text/plain; charset=UTF-8

I have been using PCB 20140316 for layout and I notice that if I auto route
tracks then create a copper pour around these tracks they will always
connect to the pour.  Even if Settings ->  New lines, arcs clear polygon is
checked.

But if I manually route these tracks then create a copper pour, I
automatically will get clearance (no connection to the plane) if Settings
->  New lines, arcs clear polygon is checked.  Or if Settings ->  New
lines, arcs clear polygon is not checked, I get no clearance or I get
connections to the plane.  This behavior meets my expectation for correct
operation.

But, I can not seem to control clearance for auto-routed tracks with copper
pours.  I am new to using the autorouter - I have been assuming that the
auto-router enforces the same DRC clearance settings, as with manual
routing.  Or is there some other settings I need to use?

Dave

--001a11c3781a98692e051ef08da6
Content-Type: text/html; charset=UTF-8
Content-Transfer-Encoding: quoted-printable

<div dir=3D"ltr"><div>I have been using PCB 20140316 for layout and I notic=
e that if I auto
 route tracks then create a copper pour around these tracks they will alway=
s connect=20
to the pour.=C2=A0 Even if Settings -&gt;=C2=A0 New lines, arcs clear polyg=
on is=20
checked. <br><br>But if I manually route these tracks then create a copper =
pour, I=20
automatically will get clearance (no connection to the plane) if Settings=
=20
-&gt;=C2=A0 New lines, arcs clear polygon is checked.=C2=A0 Or if Settings =
-&gt;=C2=A0 New lines, arcs clear polygon is not checked, I get no clearanc=
e or I get connections to the plane.=C2=A0 This behavior meets my expectati=
on for correct operation.=C2=A0 =C2=A0 <div><br></div>But, I
 can not seem to control clearance for auto-routed tracks with copper pours=
.=C2=A0=20
I am new to using the autorouter - I have been assuming that the auto-route=
r enforces the same DRC clearance settings, as with manual routing.=C2=A0 O=
r is there some other settings I need to use?=C2=A0 <br><br></div>Dave<br><=
/div>

--001a11c3781a98692e051ef08da6--

- Raw text -