X-Authentication-Warning:	delorie.com: mail set sender to geda-user-bounces using -f
X-Recipient:	geda-user AT delorie DOT com
Date:	Sun, 28 Jun 2015 20:09:59 +0200
From:	Bernd Walter <ticso AT cicely7 DOT cicely DOT de>
To:	"Rob Butts (r DOT butts2 AT gmail DOT com)" <geda-user AT delorie DOT com>
Subject:	Re: [geda-user] Stepper driver issues
Message-ID:	<20150628180958.GD94280@cicely7.cicely.de>
References:	<CALSZ9gq73RBxHV5LPe7pQWNO3kK7EPXaRiN0U7zFBV9BsQX78w AT mail DOT gmail DOT com> <55395CD0 DOT 70107 AT m0n5t3r DOT info> <20150423214501 DOT GD47936 AT cicely7 DOT cicely DOT de> <CALSZ9gqAPj6h2Z_gLvHTBdL-cnQ6p_juTonjE0e+oDAaRy7KTQ AT mail DOT gmail DOT com> <55530929 DOT 2070301 AT gmail DOT com> <CALSZ9grqsRc+U5p=LeQpzBU6_c6tWg-VrDYEqav99K_1L1P=2Q AT mail DOT gmail DOT com> <5555971C DOT 8000902 AT gmail DOT com> <CALSZ9gqtmaetZs7rHrx_sTrc1vqKkMMvDhPf0P9vs4EmuC9Q3w AT mail DOT gmail DOT com> <20150628171205 DOT GB94280 AT cicely7 DOT cicely DOT de> <CALSZ9gqeKWLzwihV4SgXtm17Jg1EGUn70NxhT+n7FgnfzMjY0g AT mail DOT gmail DOT com>
Mime-Version:	1.0
In-Reply-To:	<CALSZ9gqeKWLzwihV4SgXtm17Jg1EGUn70NxhT+n7FgnfzMjY0g@mail.gmail.com>
X-Operating-System:	FreeBSD cicely7.cicely.de 7.0-STABLE i386
User-Agent:	Mutt/1.5.11
X-Spam-Status:	No, score=-2.9 required=5.0 tests=ALL_TRUSTED=-1,BAYES_00=-1.9,T_RP_MATCHES_RCVD=-0.01 autolearn=ham version=3.3.0
X-Spam-Checker-Version:	SpamAssassin 3.3.0 (2010-01-18) on spamd.cicely.de
Reply-To:	geda-user AT delorie DOT com
Errors-To:	nobody AT delorie DOT com
X-Mailing-List:	geda-user AT delorie DOT com
X-Unsubscribes-To:	listserv AT delorie DOT com

On Sun, Jun 28, 2015 at 01:33:45PM -0400, Rob Butts (r DOT butts2 AT gmail DOT com) wrote:
> I will check the driver voltage supply since in this bread board setup it
> is the most suspect.???

Bread board is very likely an issue.
The output drivers switch high current low-side and high-side.
If ground supply of the driver module shifts relative to your microcontroller
then it can easily detect wrong signals.
It can also have problems on the power output, because of undervoltage
spikes triggering temporary driver shutdown, etc..

-- 
B.Walter <bernd AT bwct DOT de> http://www.bwct.de
Modbus/TCP Ethernet I/O Baugruppen, ARM basierte FreeBSD Rechner uvm.

- Raw text -