X-Authentication-Warning:	delorie.com: mail set sender to geda-user-bounces using -f
X-Recipient:	geda-user AT delorie DOT com
DKIM-Signature:	v=1; a=rsa-sha256; c=relaxed/relaxed;
	d=googlemail.com; s=20120113;
	h=mime-version:date:message-id:subject:from:to:content-type;
	bh=p3siXVYGwdVcURQdfT15Y/vdbVzwwCXuIjuxJ1K0BVs=;
	b=iqHYgdaiJCMFP2ZjFe1bIjJzeRWRt5UiYf/LsE28y3oqV1cEwlyBtAi2fBhw1OO7ch
	+8WMnZ25Cy0NkaI073e2a+aV8i+QMNuXj02Vo+TSOuyObvvjRouc+sbAncmM9RDE8MUe
	sEpQqxgeGX7OfSZk5KO2OU8Md/LZ86X882HrvSwx4Va/mpHJmzt/UF0MDtjCF0/59a4D
	ABUr1McXhQhQ5/Vu/LT/DqtvmPNiE+Na/mHioxhhQvWCUOYPj+HH2wTiQQAbhwGQmqN2
	T3/4dyxaf6Xd5ReeSCfoGhs753+Ef8Yo7o2baih2LhAel27qks4xgRClfAl5hCBIsYsJ
	tTHw==
MIME-Version:	1.0
X-Received:	by 10.50.97.7 with SMTP id dw7mr5944655igb.2.1382895563358; Sun,
	27 Oct 2013 10:39:23 -0700 (PDT)
Date:	Sun, 27 Oct 2013 22:09:23 +0430
Message-ID:	<CANhYM9F_CxrD4yL=rgg76m1f9sL29wNNjNn3KjYZ5xbADBQBtw@mail.gmail.com>
Subject:	Re: [geda-user] Merging ICs and nets with gsch2pcb
From:	James Jackson <james DOT a DOT f DOT jackson DOT 2 AT googlemail DOT com>
To:	geda-user AT delorie DOT com
Reply-To:	geda-user AT delorie DOT com

--047d7b10c853d0c9ca04e9bc7687
Content-Type: text/plain; charset=ISO-8859-1

Sorry for three emails in a row; just trying to make myself clear.

I've now run a test where I had a master schematic which included two
subcircuits. Each cubcircuit consisted simply of a resistor, with each pin
connected to a generic-power (nets = vcc:1 and gnd:1).

Running this through gsch2pcb results in two resistors on the PCB, but
indeed the two power nets are not connected between the subcircuits. In the
Netlist dialog, again each subcircuit has its own Vcc / Gnd nets.

I'd welcome advice on how to merge nets in this situation - I'd rather not
run power lines to each sub circuit explicitly as this will significantly
clutter up my master schematic.

Many thanks,
James.

--047d7b10c853d0c9ca04e9bc7687
Content-Type: text/html; charset=ISO-8859-1
Content-Transfer-Encoding: quoted-printable

<div dir=3D"ltr">Sorry for three emails in a row; just trying to make mysel=
f clear.<div><br></div><div>I&#39;ve now run a test where I had a master sc=
hematic which included two subcircuits. Each cubcircuit consisted simply of=
 a resistor, with each pin connected to a generic-power (nets =3D vcc:1 and=
 gnd:1).</div>
<div><br></div><div>Running this through gsch2pcb results in two resistors =
on the PCB, but indeed the two power nets are not connected between the sub=
circuits. In the Netlist dialog, again each subcircuit has its own Vcc / Gn=
d nets.</div>
<div><br></div><div>I&#39;d welcome advice on how to merge nets in this sit=
uation - I&#39;d rather not run power lines to each sub circuit explicitly =
as this will significantly clutter up my master schematic.</div><div><br>
</div><div>Many thanks,</div><div>James.</div></div>

--047d7b10c853d0c9ca04e9bc7687--

- Raw text -