X-Recipient: archive-cygwin AT delorie DOT com
X-SWARE-Spam-Status: No, hits=1.0 required=5.0 	tests=AWL,BAYES_50
X-Spam-Check-By: sourceware.org
From: "Bill Klein" <wmklein AT ix DOT netcom DOT com>
To: <cygwin AT cygwin DOT com>
References:  <67CA01A3E10441A1B929921AA2EE8E33 AT WMK> <glq2tb$bs5$1 AT ger DOT gmane DOT org>
Subject: RE: New Cygwin install and "configure: command not found" installing other packages
Date: Wed, 28 Jan 2009 11:19:06 -0600
Message-ID: <11A23EFCC31140F09CCC249D5A63569B@WMK>
MIME-Version: 1.0
Content-Type: text/plain; 	charset="us-ascii"
Content-Transfer-Encoding: 7bit
In-Reply-To: <glq2tb$bs5$1@ger.gmane.org>
X-ELNK-Trace: 61295adfd1e435c4776432462e451d7b7f19f0d9c038d9aa3dcd93957016a26316467481c4cbf7cd350badd9bab72f9c350badd9bab72f9c350badd9bab72f9c
X-IsSubscribed: yes
Mailing-List: contact cygwin-help AT cygwin DOT com; run by ezmlm
Precedence: bulk
List-Id: <cygwin.cygwin.com>
List-Unsubscribe: <mailto:cygwin-unsubscribe-archive-cygwin=delorie DOT com AT cygwin DOT com>
List-Subscribe: <mailto:cygwin-subscribe AT cygwin DOT com>
List-Archive: <http://sourceware.org/ml/cygwin/>
List-Post: <mailto:cygwin AT cygwin DOT com>
List-Help: <mailto:cygwin-help AT cygwin DOT com>, <http://sourceware.org/ml/#faqs>
Sender: cygwin-owner AT cygwin DOT com
Mail-Followup-To: cygwin AT cygwin DOT com
Delivered-To: mailing list cygwin AT cygwin DOT com

> From: cygwin-owner AT cygwin DOT com 
> [mailto:cygwin-owner AT cygwin DOT com] On Behalf Of Thorsten Kampe
> Sent: Wednesday, January 28, 2009 10:59 AM
> To: cygwin AT cygwin DOT com
> Subject: Re: New Cygwin install and "configure: command not 
> found" installing other packages
> 
> * Bill Klein (Wed, 28 Jan 2009 10:40:48 -0600)
> > I am new and know that I have done something wrong, but haven't been
> > able to find the solution in the FAQ or archives.
> > 
> > when I type
> >    .\configure
> > I am getting the 
> >   configure: command not found
> > message.
> 
> The path separator on Unix is "/". So it should be 
> "./configure". Please 
> consider getting some basic shell knowledge before using a shell.
> 
> Thorsten
> 

A) my hope is to use as little "shell" as possible.  I am installing Cygwin
in order to be able to use a specific "product" that does not (normally)
require shell programming.

B) I am using the commands as they appear in the INSTALL file for the
packages that I am using. (I simply made a typo in my original note)

C) After trying the original command, I ran this from the directory where
the "configure" file was (which I verified with "dir").

when I typed
   configure
it got the "configure: command not found" message

when I typed
   sh configure

it worked.

The file "configure" is NOT something that I created but was supplied with
the packages.  Two packages that have had this same problem are "from
reliable" sites. For example:
  http://gmplib.org/
  http://www.gnu.org/software/libtool/libtool.html
 
http://www.oracle.com/technology/software/products/berkeley-db/db/index.html


I can't believe that ALL 3 have made a mistake in their INSTALL instructions
or in their "configure" file.

I am certain, as I said, that I have done something wrong. (Possibly not
installed something in Cygwin that I should have).  However, I need help in
finding out what it is.

  


--
Unsubscribe info:      http://cygwin.com/ml/#unsubscribe-simple
Problem reports:       http://cygwin.com/problems.html
Documentation:         http://cygwin.com/docs.html
FAQ:                   http://cygwin.com/faq/