X-Authentication-Warning:	delorie.com: mail set sender to geda-user-bounces using -f
X-Recipient:	geda-user AT delorie DOT com
Message-ID:	<20180424140615.1011.qmail@stuge.se>
Date:	Tue, 24 Apr 2018 14:06:15 +0000
From:	"Peter Stuge (peter AT stuge DOT se) [via geda-user AT delorie DOT com]" <geda-user AT delorie DOT com>
To:	geda-user AT delorie DOT com
Subject:	Re: [geda-user] How to make (relay) slots in PCB
References:	<CALSZ9gpOkSYVSTrdY9jjrF82N2TpLH6MndTRD2G9K+kXjOjz1Q AT mail DOT gmail DOT com>
	<87po2pekpq DOT fsf AT gag DOT com>
	<CALSZ9goofTv8mFhNiCtTJPa1M9Z19XqPYotQUv4-s-0dr3cNfQ AT mail DOT gmail DOT com>
	<CALSZ9gofz77R10FSnDJzEXuCh09CHG8Q6goYxY8_Rno3eb29Dw AT mail DOT gmail DOT com>
MIME-Version:	1.0
In-Reply-To:	<CALSZ9gofz77R10FSnDJzEXuCh09CHG8Q6goYxY8_Rno3eb29Dw@mail.gmail.com>
Reply-To:	geda-user AT delorie DOT com
Errors-To:	nobody AT delorie DOT com
X-Mailing-List:	geda-user AT delorie DOT com
X-Unsubscribes-To:	listserv AT delorie DOT com

--C7zPtVaVf+AK4Oqc
Content-Type: text/plain; charset=us-ascii
Content-Disposition: inline
Content-Transfer-Encoding: quoted-printable

Rob Butts (r DOT butts2 AT gmail DOT com) [via geda-user AT delorie DOT com] wrote:
> The slot support page says it supports "plated slot callouts" as long as
> the slot is at least 0.04"
>=20
> I can't find how to add a callout to the component.  I'm inserting a
> screen shot of the website (hopefully)

I don't know what OSHPark mean by "callout".

Anyway, I have made the same experience as Bdale, that the board
house sometimes want the slot contour on the outline layer.

I have however also sent gerbers with overlapping holes and I got the
desired results. I've attached a footprint for the camera component
=66rom a WiiMote controller, which needs slots for its shield connections.

The holes in my footprint do not overlap by much (0.05mm) but I would
make sure that they always *do* overlap, if using this method.


//Peter

--C7zPtVaVf+AK4Oqc
Content-Type: text/plain; charset=us-ascii
Content-Disposition: attachment; filename="WiiCAM.fp"

Element[0x00000000 "WiiCAM" "U1" "" 0 0 6.75mm -3.65mm 3 100 ""]
(
	Pin[3.114mm -0.5mm 1.0mm 0.4mm 1.2mm 0.5mm "VCC" "1" "square"]
	Pin[2.23mm -2mm 1.0mm 0.4mm 1.2mm 0.5mm "GND" "2" ""]

	Pin[1.346mm -0.5mm 1.0mm 0.4mm 1.2mm 0.5mm "GND" "3" ""]
	Pin[0.462mm -2mm 1.0mm 0.4mm 1.2mm 0.5mm "NC" "4" ""]

	Pin[-0.422mm -0.5mm 1.0mm 0.4mm 1.2mm 0.5mm "SCL" "5" ""]
	Pin[-1.306mm -2mm 1.0mm 0.4mm 1.2mm 0.5mm "SDA" "6" ""]

	Pin[-2.19mm -0.5mm 1.0mm 0.4mm 1.2mm 0.5mm "CLK_25MHz" "7" ""]
	Pin[-3.074mm -2mm 1.0mm 0.4mm 1.2mm 0.5mm "nRESET" "8" ""]

	Pin[-1.15mm 1.6mm 0 0.4mm 1.6mm 1.4mm "" "PEG" "hole"]
	Pin[2.42mm 1.6mm 0 0.4mm 1.6mm 1.4mm "" "PEG" "hole"]

	Pin[-5.25mm -0.068mm 1.4mm 0.4mm 1.6mm 0.6mm "" "SHIELD" ""]
	Pin[-5.25mm 0.482mm 1.4mm 0.4mm 1.6mm 0.6mm "" "SHIELD" ""]
	Pin[-5.25mm 1.032mm 1.4mm 0.4mm 1.6mm 0.6mm "" "SHIELD" ""]

	Pin[5.25mm -0.068mm 1.4mm 0.4mm 1.6mm 0.6mm "" "SHIELD" ""]
	Pin[5.25mm 0.482mm 1.4mm 0.4mm 1.6mm 0.6mm "" "SHIELD" ""]
	Pin[5.25mm 1.032mm 1.4mm 0.4mm 1.6mm 0.6mm "" "SHIELD" ""]

	ElementLine[-5.25mm -3.7mm -5.25mm -1.0mm 0.15mm]
	ElementLine[-5.25mm 2.0mm -5.25mm 2.8mm 0.15mm]

	ElementLine[-5.25mm 2.8mm -2.8mm 2.8mm 0.15mm]
	ElementLine[-2.8mm 2.8mm -2.8mm 3.7mm 0.15mm]
	ElementLine[-2.8mm 3.7mm 2.8mm 3.7mm 0.15mm]
	ElementLine[2.8mm 3.7mm 2.8mm 2.8mm 0.15mm]
	ElementLine[2.8mm 2.8mm 5.25mm 2.8mm 0.15mm]

	ElementLine[5.25mm 2.8mm 5.25mm 2.0mm 0.15mm]
	ElementLine[5.25mm -1.0mm 5.25mm -3.7mm 0.15mm]
	ElementLine[5.25mm -3.7mm -5.25mm -3.7mm 0.15mm]
)

--C7zPtVaVf+AK4Oqc--

- Raw text -