X-Authentication-Warning:	delorie.com: mail set sender to geda-user-bounces using -f
X-Recipient:	geda-user AT delorie DOT com
DKIM-Signature:	v=1; a=rsa-sha256; c=relaxed/relaxed;
	d=gmail.com; s=20120113;
	h=mime-version:in-reply-to:references:date:message-id:subject:from:to
	:content-type:content-transfer-encoding;
	bh=IHb26cxphDFguVkoOcRBZGChs8RPTZzJ77TeRMPWa7c=;
	b=rMQm/x+GIoL5C7e6gbJeeM5+fijxIc7MiyyHd8i3ZX0yhoBjEtV9ofGiU2BPBxStMH
	9r4o7B4SmROWQdnKyaRfjbInHx7domTvXYKTpmmbS/215fgtHM0v8rc4D7GJUaTwI8GD
	Ggp/Tu3NOuLhQUvalvKhgqg6hPuW9LCba7m1Dz1u7mtd8X2GUp8IQRZDmw/AbQyr6Z8q
	bkGY4kUO/HvDE5dXf3K3DSCfUX0AUM4Yb9vxqXoKKCB0Lcjy9aaviNtivV9EEnPIykBJ
	pPqdPgBdb7FsbjcSwSD6HNH68EqdmSDiMd6/wIlqGN8/JDqwUKtUZr/q4fiz8JYwkwfI
	Qjhw==
MIME-Version:	1.0
X-Received:	by 10.182.199.70 with SMTP id ji6mr25426203obc.3.1425991770086;
	Tue, 10 Mar 2015 05:49:30 -0700 (PDT)
In-Reply-To:	<CAHLh21A=Lh3nBm5bXp7pOty79+0vaWpXkPiEPQWTHoc16TCEXw@mail.gmail.com>
References:	<CAHLh21A=Lh3nBm5bXp7pOty79+0vaWpXkPiEPQWTHoc16TCEXw AT mail DOT gmail DOT com>
Date:	Tue, 10 Mar 2015 15:49:30 +0300
Message-ID:	<CAOxVtSR=9ZhY_S66_hsDxYtRttL+y-KdGKxZ4hqk_LDzmz+ogg@mail.gmail.com>
Subject:	Re: [geda-user] pcb doesn't show nets
From:	Sergey Alyoshin <alyoshin DOT s AT gmail DOT com>
To:	geda-user AT delorie DOT com
X-MIME-Autoconverted:	from quoted-printable to 8bit by delorie.com id t2ACnYBu007603
Reply-To:	geda-user AT delorie DOT com
Errors-To:	nobody AT delorie DOT com
X-Mailing-List:	geda-user AT delorie DOT com
X-Unsubscribes-To:	listserv AT delorie DOT com

On Tue, Mar 10, 2015 at 3:32 PM, Александр Ушанов <alushanov92 AT gmail DOT com> wrote:
> Hello, I created simple schematic with to connected connectors just for
> check gEDA(one.sch) and in pcb(one.pcb) after load nets from file I see no
> yellow lines, but I can open other pcb, created by my friend and see nets. I
> can see my nets and pins witch connected to nets in netlist.
> For both elements I used footprints from
> /usr/share/pcb/newlib/headers/0.1_inch_2pin (installed from official gentoo
> tree with geda package).
> Is it bug or I did something wrong?

Press 'O' (optimize rats nest).

- Raw text -