X-Authentication-Warning:	delorie.com: mail set sender to geda-user-bounces using -f
X-Recipient:	geda-user AT delorie DOT com
DKIM-Signature:	v=1; a=rsa-sha256; c=relaxed/relaxed;
	d=gmail.com; s=20120113;
	h=mime-version:in-reply-to:references:date:message-id:subject:from:to
	:content-type;
	bh=rYiXky/LEFX0UY9MUd25DoIGC9NAZax+2arP4qxfZds=;
	b=rv11XvgeXbsBmYDzuTBFVtYXs/SLcMQ7QZNNZL0LIwisiXjlfABNiTPsucc6j/ZCRT
	UbXbMy4NOmoMljMYU7vqsJEMepjPCAVG9XhEayJdK0fE6e1tjt0bD8s4zjV7ChL2Ov8Y
	HAcH7aLkJxVb6SfJtOW5qr10dVRDxEX89GryQ+yqv3nnbnYlD1BwO007MmObU6z8jifY
	BekiPcw+3A6R/uTSoruLfxQwUnH+C355DShEARwZ02YIIaY+YPh1duF94MBJvfi2W8uF
	50LclAesEnFUfjakgmFlVdlG2H+LSygritLSGNwYQzGwpT8GjFW2xtVDSqrNlcSQ6jax
	3stQ==
MIME-Version:	1.0
X-Received:	by 10.220.145.132 with SMTP id d4mr19328953vcv.9.1377597215372;
	Tue, 27 Aug 2013 02:53:35 -0700 (PDT)
In-Reply-To:	<521C6317.7070605@iae.nl>
References:	<521B22D8 DOT 3030707 AT iae DOT nl>
	<CAMvDHVCZm+dYkFrbWoBMbnGvEv_nxr_OG+J3HM5EShhtd6kDBQ AT mail DOT gmail DOT com>
	<521C6317 DOT 7070605 AT iae DOT nl>
Date:	Tue, 27 Aug 2013 13:53:35 +0400
Message-ID:	<CAMvDHVCSRjqYw_wm7vO+qbX+bz373S=cvpN2zJ6_ZUC+WdL1bw@mail.gmail.com>
Subject:	Re: [geda-user] Tutorial: VHDL with gEDA
From:	Vladimir Zhbanov <vzhbanov AT gmail DOT com>
To:	geda-user AT delorie DOT com
Reply-To:	geda-user AT delorie DOT com
Errors-To:	nobody AT delorie DOT com
X-Mailing-List:	geda-user AT delorie DOT com
X-Unsubscribes-To:	listserv AT delorie DOT com

Pin types are related to pins which are parts of their symbols.
pintype= is an attribute of a pin, not a symbol attribute, so it
specifies the signal direction for the pin. Thus, if a pin is
INPUT for you XOR symbol, it should have the pintype=in attribute
but the port symbol representing it within the sub-schematic is
not a pin. The pin of the port should have pintype=out since it is
an output for _the port symbol_.

I hope, the signal direction shown below should clear this.

external   | XOR subcircuit
pin        |
           | -----------\   pin of the port symbol
-->INPUT-->| |INPUT PORT >-->OUTPUT of the port-->
pintype=in | -----------/   pintype=out
           |

I noticed one issue with the ipad symbol, though. As far as I know,
the pintype attribute values should be written in lower case
according to the Master Attribute List Document.

- Raw text -