X-Authentication-Warning:	delorie.com: mail set sender to geda-user-bounces using -f
X-Recipient:	geda-user AT delorie DOT com
DKIM-Signature:	v=1; a=rsa-sha256; c=relaxed/relaxed;
	d=gmail.com; s=20120113;
	h=mime-version:in-reply-to:references:date:message-id:subject:from:to
	:content-type;
	bh=D+7frJ/tgah9VkcyKEVqS5S9gYzFDZC6XuPUIS19KbI=;
	b=RV5KFYHDdBJg9r2wrCkrLpQqDZdZUBj1sG/CWCHrksD/xR7YavojO/X0ispHCDY0sh
	QihoIUPRbw9e47I+yoQ6oTbLuGt9WRRVQb9LhXLC2UDE5+Urq63J7jE7zbi9YYPnhLpt
	Bkxz8iCVKZIMgKQaXQusFFySPnSKUIkMCEBQe7JlYMctuluw2O8UX+1F3Hg6t8KYkHgP
	SzlVaiRA+VcNn2rqwubL/GXRLp5z8hHxydbFKI+Yg4/ZFYcACVnoEpc5Vh+VUvRoO2Lc
	URStuwJMmeEnHIhizHMeDY/xuYwM8J/Kv3sYXhMlBAGLaOoMY/vABugJYZ5Plvf/FvHL
	vsQw==
MIME-Version:	1.0
In-Reply-To:	<CAOuGh89gaE0N8JFaAV03rzrJ_aFH3vMBDoKV=F_qwqnXRX-KyA@mail.gmail.com>
References:	<CACwWb3DPSG8YgiTsHnfbQE0uyE7X57wPUG4+6-1+XAObLZ=x2Q AT mail DOT gmail DOT com>
	<CAOuGh886P23RT+prmwe5mt9pJv-XZ=_ThL8hW0X4aSoWn_S0Ng AT mail DOT gmail DOT com>
	<CACwWb3CXakvZ25+vCbKXFDPqKPxj6ErjojWOvuChoXKJZ_8L9Q AT mail DOT gmail DOT com>
	<CAOuGh89gaE0N8JFaAV03rzrJ_aFH3vMBDoKV=F_qwqnXRX-KyA AT mail DOT gmail DOT com>
Date:	Sat, 1 Sep 2012 09:14:18 +0800
Message-ID:	<CANDNR8r2srqUxaGEsC1VyZ0eP==FQ5e6-9XBwcx584Hf9gM9eA@mail.gmail.com>
Subject:	Re: [geda-user] [OFF] scripting inside an MCU
From:	Atommann <atommann AT gmail DOT com>
To:	geda-user AT delorie DOT com
Reply-To:	geda-user AT delorie DOT com
Errors-To:	nobody AT delorie DOT com
X-Mailing-List:	geda-user AT delorie DOT com
X-Unsubscribes-To:	listserv AT delorie DOT com

2012/8/31 Bob Paddock <graceindustries AT gmail DOT com>:
> On Fri, Aug 31, 2012 at 10:02 AM, Levente <leventelist AT gmail DOT com> wrote:
>> Thanks. I guess it is overkill for the task. I have an MCU with 128k flash.
>
> Don't think it is much over 6K, at least it was the last time I used
> it, been a while.
> RAM might be more of an issue that Flash.
>
> If you are hurting for space there is always Forth.

I think Forth can meet the requirements of Levente, and there is some
Forth implementation for AVRs.
I wrote a tutorial when I was learning Forth, though the article is in
Chinese, but there are many photos.(at the end of the article, you can
see how to use a bluetooth module to act as the comms interface thus
you can update the firmware of the mcu without a cable)

Using Arduino's hardware to  experience amforth
http://www.atommann.com/learn/amforth/helloworld.html

-- 
Best regards,
Atommann

- Raw text -