X-Authentication-Warning:	delorie.com: mail set sender to geda-help-bounces using -f
X-Recipient:	geda-help AT delorie DOT com
DKIM-Signature:	v=1; a=rsa-sha256; c=relaxed/relaxed;
	d=gmail.com; s=20120113;
	h=date:from:to:subject:message-id:mail-followup-to:references
	:mime-version:content-type:content-disposition:in-reply-to
	:user-agent;
	bh=YAKjIEO4riR86o7CZIy4gEtc8TbgnUSBU06RYz1Dew0=;
	b=g6aw8CYSG2IPAiBZlV0HPEEmFK6/6L80yHs2r26U0XVsAV3GZykhFTDKW65wWhvr1d
	PdxP+OvXiMb2aPmhJAqJpK09JN1EuEAvvpQ8Oiprc5UYwqlvG+d3ICqvcLrcZq/+twhp
	I0jXQ7L1OyPj7nhWVfb20u0bBX2HW7tnoIdZ7UvskkO+M45sL7IBWK1maBjagu97dRdJ
	WZmopWAX9ygJmCUc2IG/pi29ENNIHbOpjJFQHREZy9pIKLfsJVCs6iwGF3A/VVX5iMVD
	ZBtLk3wKC/5m7Fy42ouV2FvR1Rq9/cNC5RhEwK3QRisuKaoKXq3X17qFf1FLoJCgwNq2
	YpUA==
X-Received:	by 10.152.206.67 with SMTP id lm3mr12724598lac.16.1416218198207;
	Mon, 17 Nov 2014 01:56:38 -0800 (PST)
Date:	Mon, 17 Nov 2014 12:56:35 +0300
From:	Vladimir Zhbanov <vzhbanov AT gmail DOT com>
To:	geda-help AT delorie DOT com
Subject:	Re: [geda-help] newbie: automatic way to find a model
Message-ID:	<20141117095634.GA23131@localhost.localdomain>
Mail-Followup-To:	geda-help AT delorie DOT com
References:	<CAJvHTNzU26FpikzGkmkx6xcZawUZWMFSKkfeSnHALhZ8j5RFGQ AT mail DOT gmail DOT com>
MIME-Version:	1.0
In-Reply-To:	<CAJvHTNzU26FpikzGkmkx6xcZawUZWMFSKkfeSnHALhZ8j5RFGQ@mail.gmail.com>
User-Agent:	Mutt/1.5.23 (2014-03-12)
Reply-To:	geda-help AT delorie DOT com
Errors-To:	nobody AT delorie DOT com
X-Mailing-List:	geda-help AT delorie DOT com
X-Unsubscribes-To:	listserv AT delorie DOT com

On Thu, Oct 30, 2014 at 12:05:15AM +1100, Jack Andrews wrote:
>    Hi,
>    My interest is
>     - bread-boarding some hardware ideas
>     - saving time messing with hardware by using simulation
>    So I ended up looking at [ng]spice and gschem
>    This is my first day and I'm quite pleased with my progress - all
>    credit due to gEDA.
>    I drew up the start of a current mirror in gschem and
>    $ gnetlist -v -g spice-sdb current-mirror   #see current mirror in
>    shell script below
>    and the body of the output was:
>    B2 5 7 0V
>    R4 1 unconnected_pin-1 7 5K
>    B1 7 6 12V
>    Q1 2 2 6 unknown
>    Q2 4 2 6 unknown
>    R3 3 5 5K
>    R2 4 3 10K
>    R1 2 1 10K
>    .end
>    In my schematic, I specified Q{1,2} as 2N2222 - but to run ngspice, I
>    seem to need to find the model for 2N2222.  I'm sure the question has
>    been asked before:
>      . is there an automated way to find the model for 2N2222?
Probably spicelib could help you. Please read [1] and search for the
link there.

>    If this is currently done manually, I'd like to contribute some work.
>    (I'm in software by day).
>    Also, note the R4 VARIABLE_RESISTOR is being used as a variable
>    resistor (not a potentiometer) so there is a floating node.  What is
>    the best way of drawing what I want?  And then, how do I get spice to
>    vary the resistor in 33 steps?  Maybe use a VCR
>    voltage-controlled-resistor and vary the voltage control?  Starting to
>    get vague now...
I think you ought to read the "Parameter sweep" section in the ngspice
manual. For your resistor you can make a subschematic with two resistors
in it.

HTH,
  Vladimir

[1] http://wiki.geda-project.org/geda:ngspice_and_gschem

- Raw text -