X-Authentication-Warning:	delorie.com: mail set sender to geda-help-bounces using -f
X-Recipient:	geda-help AT delorie DOT com
X-Spam-Checker-Version:	SpamAssassin 3.3.1 (2010-03-16) on
	ham01.websitewelcome.com
X-Spam-Flag2999:	NO
X-Spam-Level2999:
X-Spam-Status2999:	"No, score=-1.9 required=5.0 tests=BAYES_00 autolearn=ham
	version=3.3.1
DomainKey-Signature:	a=rsa-sha1; q=dns; c=nofws; s=default; d=gibibit.com;
	h=Received:Date:From:To:Subject:Message-ID:In-Reply-To:References:X-Mailer:Mime-Version:Content-Type:X-BWhitelist:X-Source:X-Source-Args:X-Source-Dir:X-Source-Sender:X-Source-Auth:X-Email-Count:X-Source-Cap;
	b=CZp0ZdZ7vHmnah++0HIGATy6Oaaq0KDRnhMjQ4VjgMPTxUhroyXJam5cYeHRzIa/QGImbO3/kia7YPDUc5D6Cr8Wclmftez7aDN+EJNQirhQC25yEPkjX+6FcdeqNLUy;
Date:	Wed, 8 Feb 2012 09:19:29 -0800
From:	Colin D Bennett <colin AT gibibit DOT com>
To:	geda-help AT delorie DOT com
Subject:	Re: [geda-help] polygon shaped hole in solder mask
Message-ID:	<20120208091929.5159a6a5@svelte>
In-Reply-To:	<20120208071321.GA14573@geminiman>
References:	<20120208071321 DOT GA14573 AT geminiman>
X-Mailer:	Claws Mail 3.7.9 (GTK+ 2.24.6; x86_64-pc-linux-gnu)
Mime-Version:	1.0
X-AntiAbuse:	This header was added to track abuse, please include it with any abuse report
X-AntiAbuse:	Primary Hostname - gator297.hostgator.com
X-AntiAbuse:	Original Domain - delorie.com
X-AntiAbuse:	Originator/Caller UID/GID - [47 12] / [47 12]
X-AntiAbuse:	Sender Address Domain - gibibit.com
X-BWhitelist:	no
X-Source:
X-Source-Args:
X-Source-Dir:
X-Source-Sender:	c-67-185-118-84.hsd1.wa.comcast.net (svelte) [67.185.118.84]:41710
X-Source-Auth:	colin AT gibibit DOT com
X-Email-Count:	6
X-Source-Cap:	c2t5bGVuO3NreWxlbjtnYXRvcjI5Ny5ob3N0Z2F0b3IuY29t
Reply-To:	geda-help AT delorie DOT com
Errors-To:	nobody AT delorie DOT com
X-Mailing-List:	geda-help AT delorie DOT com
X-Unsubscribes-To:	listserv AT delorie DOT com

--Sig_/FZ.lwkIYGl9vBlBM8Vn/HJN
Content-Type: text/plain; charset=UTF-8
Content-Transfer-Encoding: quoted-printable

On Wed, 8 Feb 2012 01:13:21 -0600
mog <mog-lists AT rldn DOT net> wrote:

> Hi I am trying to do something similar to this
> http://www.commerce.com.tw/tlPic2002/12850340172204.jpg
> I already have my logo in the component layer and have cleared
> the area around it from my ground plain so it should be good
> to go but I can't figure out how to remove the solder mask
> from covering my polygon.  Is this possible in pcb?

How did you make your logo in the component layer?  Is it made with
polygons or with lines?  Could you post a .pcb file with the logo?

If it is made with lines, you could convert it to an element (thus
converting the =E2=80=9Cline=E2=80=9D entities into =E2=80=9Cpad=E2=80=9D e=
ntities) and then the
pads will automatically clear the solder mask.

If it is made with polygons, you are out of luck.  I think.  It's
really too bad that pcb footprints are so restricted.

Regards,
Colin

--Sig_/FZ.lwkIYGl9vBlBM8Vn/HJN
Content-Type: application/pgp-signature; name=signature.asc
Content-Disposition: attachment; filename=signature.asc

-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)

iEUEARECAAYFAk8yrqEACgkQokx8fzcGbYfYSgCaAhdYEtysxHfWotF3sYuoVUoQ
CDcAlRzaVQqWu5FKCJc66Zs9+zXickQ=
=Kux7
-----END PGP SIGNATURE-----

--Sig_/FZ.lwkIYGl9vBlBM8Vn/HJN--

- Raw text -