Mailing-List:	contact cygwin-help AT cygwin DOT com; run by ezmlm
List-Subscribe:	<mailto:cygwin-subscribe AT cygwin DOT com>
List-Archive:	<http://sources.redhat.com/ml/cygwin/>
List-Post:	<mailto:cygwin AT cygwin DOT com>
List-Help:	<mailto:cygwin-help AT cygwin DOT com>, <http://sources.redhat.com/ml/#faqs>
Sender:	cygwin-owner AT cygwin DOT com
Mail-Followup-To:	cygwin AT cygwin DOT com
Delivered-To:	mailing list cygwin AT cygwin DOT com
X-Authentication-Warning:	slinky.cs.nyu.edu: pechtcha owned process doing -bs
Date:	Thu, 22 May 2003 23:52:32 -0400 (EDT)
From:	Igor Pechtchanski <pechtcha AT cs DOT nyu DOT edu>
Reply-To:	cygwin AT cygwin DOT com
To:	luke DOT kendall AT cisra DOT canon DOT com DOT au
cc:	cygwin AT cygwin DOT com
Subject:	Re: Setup failures during mirrored install
In-Reply-To:	<20030523023935.0882A34C53@nevin.research.canon.com.au>
Message-ID:	<Pine.GSO.4.44.0305222349010.26092-100000@slinky.cs.nyu.edu>
Importance:	Normal
MIME-Version:	1.0

Luke,

I've explicitly set Reply-To: to point to the list.  Please make sure your
mailer honors that in the future.  Thanks.

More comments below.

On Fri, 23 May 2003 luke DOT kendall AT cisra DOT canon DOT com DOT au wrote:

> On 22 May, Igor Pechtchanski wrote:
> >  Define "hung"?  100% CPU?  0% CPU?  What was on the screen at the time?
> >  Did setup react to Windows events (i.e., could you cancel it)?  Would you
> >  be willing to try a debug snapshot of setup, attach to it with gdb when it
> >  hangs, and post a backtrace for each thread?
>
> Sorry, I should have been clearer.
>
> I meant that setup's progress simply stopped.  I could still cancel it,
> so it was still responding to mouse events.  Also, the system CPU load
> was low, and the network traffic was low.

Sounds like it's waiting for some event in one of the threads, but no
other thread sent the event...  The backtraces should be more informative,
though.

> I'd be willing to try a debug snapshot.  I haven't used gdb to debug
> threads though.
>
> I assume I run ps and use the PID, not the WINPID to attach to?
> What are the commands to list threads, and attach to a thread?
>
> Or do you simply say "thread apply all where" ?
>
> luke

The debugging snapshot is available at <http://cygwin.com/setup-snapshots/>.
Just run gdb, attach to the Cygwin PID, and use "info threads" to list all
threads.  Then switch to each thread by using "thread <n>", where <n> is
the thread number, and use "where" or "bt" to get a backtrace.
	Igor
-- 
				http://cs.nyu.edu/~pechtcha/
      |\      _,,,---,,_		pechtcha AT cs DOT nyu DOT edu
ZZZzz /,`.-'`'    -.  ;-;;,_		igor AT watson DOT ibm DOT com
     |,4-  ) )-,_. ,\ (  `'-'		Igor Pechtchanski
    '---''(_/--'  `-'\_) fL	a.k.a JaguaR-R-R-r-r-r-.-.-.  Meow!

"I have since come to realize that being between your mentor and his route
to the bathroom is a major career booster."  -- Patrick Naughton


--
Unsubscribe info:      http://cygwin.com/ml/#unsubscribe-simple
Problem reports:       http://cygwin.com/problems.html
Documentation:         http://cygwin.com/docs.html
FAQ:                   http://cygwin.com/faq/

- Raw text -