Mailing-List:	contact cygwin-help AT sourceware DOT cygnus DOT com; run by ezmlm
Sender:	cygwin-owner AT sourceware DOT cygnus DOT com
Delivered-To:	mailing list cygwin AT sourceware DOT cygnus DOT com
Message-ID:	<01ce01bea20c$7c7f5720$29acdfd0@InspirePharm.Com>
Reply-To:	"Suhaib M. Siddiqi" <ssiddiqi AT ipass DOT net>
From:	"Suhaib M. Siddiqi" <ssiddiqi AT ipass DOT net>
To:	<cygwin AT sourceware DOT cygnus DOT com>, "Linda Seymour" <lseymour AT eti DOT com>
References:	<4 DOT 1 DOT 19990519092732 DOT 00a70e70 AT mail DOT eti DOT com>
Subject:	Re: Cygwin Imake
Date:	Wed, 19 May 1999 11:30:11 -0400
MIME-Version:	1.0
X-Priority:	3
X-MSMail-Priority:	Normal
X-Mailer:	Microsoft Outlook Express 5.00.2014.211
X-MimeOLE:	Produced By Microsoft MimeOLE V5.00.2014.211
X-MIME-Autoconverted:	from quoted-printable to 8bit by delorie.com id LAA01906

Linda

> I downloaded Cygwin X11R6 tools and I am trying to use the Imake that was
> provided.  I get the following error when I try and make my Makefile:
> 


From where you downloaded X11R6 tools? From Sergey, mine or some other site?

> > config/imake/nt/imake -I./config/cf -DTOPDIR=. -DCURDIR=.   
> gcc: installation problem, cannot exec `cpp': No such file or directory
> config/imake/nt/imake: Exit code 1.
>   Stop.
> 

This is not an Imake error.
This is gcc installation problem.  You have a bad gcc installation.


> We don't have a cpp.exe.  We did try renaming c++.exe and gcc.exe but this
> did not work.  I have
> another Imake that I don't know where it is from but when I use that one I
> have problems with the
> cygwin sh.exe.
> 

ALL of this is absolutely not allowed.  Renaming gcc.exe or g++.exe to cpp.exe is NOT
permitted at all.
Of cource you have cpp.exe, if you  have gcc installed properly.


> This other Imake works fine with MKS NT tools but I want to get away from
> using the MKS NT tools.
> 

I am not aware of an IMAKE.EXE from MKS NT tools.  Correct me,  as far as I know MKS (aka DataFocus) does not provide X11 stuff with NT tools, unless you license Nutcraker from them.

> I found on the FAC were It tells me that I need to set an environment
> variable GCC_EXEC_PREFIX but
> it does not tell me what to set it to. 
> 

You need to read a good book on GNU tools.  I think http://www.delorie.com
DJ Delorie has some very good references on books which might help you.

I hope this help

Regards
Suhaib

> So, does anyone have any suggestions on solving this problem?
> Linda Seymour
> email:    lseymour AT eti DOT com 
> Direct phone: (512) 383-3155
> 
> Evolutionary Technologies International, Inc.  Switchboard: (512) 383-3000
> Frost Bank Plaza fax:   (512) 383-3300
> 816 Congress Avenue, Suite 1300
> Austin, Texas  78701
> 
> 
> --
> Want to unsubscribe from this list?
> Send a message to cygwin-unsubscribe AT sourceware DOT cygnus DOT com
> 
> 


--
Want to unsubscribe from this list?
Send a message to cygwin-unsubscribe AT sourceware DOT cygnus DOT com

- Raw text -