X-Authentication-Warning: delorie.com: mail set sender to geda-user-bounces using -f
X-Recipient: geda-user AT delorie DOT com
X-Original-DKIM-Signature: v=1; a=rsa-sha1; c=relaxed; d=sendgrid.net; 
	h=subject:to:references:from:mime-version:in-reply-to:content-type:content-transfer-encoding; 
	s=smtpapi; bh=AqSAZeohhBkUZjuZGyyumXNa1aY=; b=e8jvO9mAngS9wTC9Xy
	fVzP502wobMXhvn+YBG7qPIZGzgkRBHXIh8JPoGEece2RhE90zQt/aCwhLfEk7SJ
	62wmkFOrpQczt6HMqPQG1qkQVjYTBkYEDWbLN7lo4ATDihKxEl54jvQVN/OjTxTR
	6x1kJxFZfcXPT/2CSUvSH5Zr0=
Subject: Re: [geda-user] thru hole slots in PCB
To: geda-user AT delorie DOT com
References: <411d8c80-deab-4bc4-2a97-9bb6829a7b7f AT ecosensory DOT com>
 <29718f67-b9a0-4d13-5d9c-c987433635e0 AT neurotica DOT com>
From: "John Griessen (john AT ecosensory DOT com) [via geda-user AT delorie DOT com]" <geda-user AT delorie DOT com>
Message-ID: <d95f1978-fbed-0050-904b-54f3533904bc@ecosensory.com>
Date: Fri, 13 Jan 2017 11:36:22 -0600
User-Agent: Mozilla/5.0 (X11; Linux x86_64; rv:45.0) Gecko/20100101
 Icedove/45.4.0
MIME-Version: 1.0
In-Reply-To: <29718f67-b9a0-4d13-5d9c-c987433635e0@neurotica.com>
Content-Type: text/plain; charset=utf-8; format=flowed
Content-Transfer-Encoding: 7bit
X-SG-EID: V53lTA/kUP1+IqXnzXuv0M/cu/N8aMtf7nxyAyKnAksGtNIt9jRk0Ht2WwkFCwAc71pxNhZy+8Zt86
 hrAS+XCHXMhC6eewH8nUuSZjgy9BBDnOxXPifSijgTzrWnDzwVKA74IvKsjesSH2wJqDk+2nWEgORC
 Nn+tq0RoBtXferglDhlbEafuiJzlY+wU77sXMnLTyFzvR3c/KbHt3vuKOpNXIn+JRnPPsMxV3ZpkIa
 U=
Reply-To: geda-user AT delorie DOT com
Errors-To: nobody AT delorie DOT com
X-Mailing-List: geda-user AT delorie DOT com
X-Unsubscribes-To: listserv AT delorie DOT com
Precedence: bulk

On 01/13/2017 09:19 AM, Dave McGuire (mcguire AT neurotica DOT com) [via geda-user AT delorie DOT com] wrote:
>   When I last needed to use a component with tab leads, which was a
> coaxial power connector, I ended up using a hole large enough.  That
> board went to volume; it really pissed off the assembly firm due to the
> positional variation.  The part's tabs floated around within its three
> holes quite a bit.  It was fine due to the wide tolerances in the
> chassis the board mounted in, but the assembly guys didn't like it at all.

So, that sounds like the assembly shop had no trouble placing parts, just
that they fretted over the process variation it caused?

John