X-Authentication-Warning: delorie.com: mail set sender to geda-user-bounces using -f
X-Recipient: geda-user AT delorie DOT com
X-Original-DKIM-Signature: v=1; a=rsa-sha1; c=relaxed; d=sendgrid.net; 
	h=subject:to:references:from:mime-version:in-reply-to:content-type:content-transfer-encoding; 
	s=smtpapi; bh=S0XA8zB6EnOtWL3kZxCyvyYRZ+o=; b=HHtUr81W0EY+b8aFIO
	+3y1aZc8dU1tzDAzbo2vZMG0FM5mzZ7dP25XEt4g91BvCmDARIPuCCSPTcSd4F/h
	lbtrG0qhPr6wFlfFN2tJfz7nYurGi5kb80zCjTzzI7gZvHO3kpGNZn4ypvmJXy2v
	TJfbsJbnqAipABBgBPwPOe1vw=
Subject: Re: [geda-user] pcb file format
To: geda-user AT delorie DOT com
References: <0d49697a-80c7-d588-859a-56bc542f7e5d AT ecosensory DOT com>
 <f54225e8-dfc4-e160-ef35-f332615eafb1 AT gmail DOT com>
 <e44ac11b-f069-3ae3-e489-8cbb89863e99 AT ecosensory DOT com>
 <0e07c994-a50f-6daa-709b-420a58121cc2 AT gmail DOT com>
From: "John Griessen (john AT ecosensory DOT com) [via geda-user AT delorie DOT com]" <geda-user AT delorie DOT com>
Message-ID: <5bdfba40-3e08-cf68-f9e8-512ce5eb14e8@ecosensory.com>
Date: Sat, 12 Nov 2016 20:06:29 -0600
User-Agent: Mozilla/5.0 (X11; Linux x86_64; rv:45.0) Gecko/20100101
 Icedove/45.4.0
MIME-Version: 1.0
In-Reply-To: <0e07c994-a50f-6daa-709b-420a58121cc2@gmail.com>
Content-Type: text/plain; charset=windows-1252; format=flowed
Content-Transfer-Encoding: 7bit
X-SG-EID: V53lTA/kUP1+IqXnzXuv0M/cu/N8aMtf7nxyAyKnAkt7e0xKZKhBT9MoiceG7tLrEEO4O+pKrIHFsa
 OmA87jiebdkcQUWj7pFJncEoTfOouy2f6NyecF3ykD7BZxnM2tEqU7CdDkPCnqDBJV3nVPVCryWW8R
 WZpb8R77QFl1RlEk21/eNIV1FrNDPi3xoRDbhHJ5T4ykEF2YQmjNVpQkJanonZuab8uxgOrUB6uJSk
 w=
Reply-To: geda-user AT delorie DOT com
Errors-To: nobody AT delorie DOT com
X-Mailing-List: geda-user AT delorie DOT com
X-Unsubscribes-To: listserv AT delorie DOT com
Precedence: bulk

On 11/12/2016 01:39 PM, Charles Repetti (charlie94965 AT gmail DOT com) [via geda-user AT delorie DOT com] wrote:
> I use a contract fab/assembly, I've never worked directly with a stencil for one of my designs, though I've seen them at trade shows.

Yes, and I mentioned other ways to promote how good the gEDA workflow is getting for  open source hardware,
which can very much benefit from early adopter fab runs in a garage with a toaster oven controlled by such as this:

https://www.tindie.com/products/nsayer/toast-r-reflow-controller