X-Authentication-Warning: delorie.com: mail set sender to geda-user-bounces using -f
X-Recipient: geda-user AT delorie DOT com
Date: Thu, 30 Jul 2015 13:33:46 +0200 (CEST)
X-X-Sender: igor2 AT igor2priv
To: "Wojciech Kazubski (wk AT ire DOT pw DOT edu DOT pl) [via geda-user AT delorie DOT com]" <geda-user AT delorie DOT com>
X-Debug: to=geda-user AT delorie DOT com from="gedau AT igor2 DOT repo DOT hu"
From: gedau AT igor2 DOT repo DOT hu
Subject: Re: [geda-user] yet another footprint generator
In-Reply-To: <sig.365312e466.13318802.nfOMCWsRbR@jawor>
Message-ID: <alpine.DEB.2.00.1507301331540.6924@igor2priv>
References: <alpine DOT DEB DOT 2 DOT 00 DOT 1507162039300 DOT 6924 AT igor2priv> <alpine DOT DEB DOT 2 DOT 00 DOT 1507170609560 DOT 6924 AT igor2priv> <alpine DOT DEB DOT 2 DOT 00 DOT 1507170712420 DOT 6924 AT igor2priv> <sig DOT 365312e466 DOT 13318802 DOT nfOMCWsRbR AT jawor>
User-Agent: Alpine 2.00 (DEB 1167 2008-08-23)
MIME-Version: 1.0
Content-Type: TEXT/PLAIN; charset=US-ASCII; format=flowed
Reply-To: geda-user AT delorie DOT com
Errors-To: nobody AT delorie DOT com
X-Mailing-List: geda-user AT delorie DOT com
X-Unsubscribes-To: listserv AT delorie DOT com
Precedence: bulk



On Thu, 30 Jul 2015, Wojciech Kazubski (wk AT ire DOT pw DOT edu DOT pl) [via geda-user AT delorie DOT com] wrote:

> Dnia pi?tek, 17 lipca 2015 07:18:45 piszesz:
>> On Fri, 17 Jul 2015, gedau AT igor2 DOT repo DOT hu wrote:
>>> I am going to add more optional parameters this weekend:
>>> <snip>
>>> even rows should be shifted by half
>>
>> I had a 15 minutes free slot this morning so added this too (optional
>> parameters eshift and etrunc):
>>
>> http://igor2.repo.hu/cgi-bin/pcblib-param.cgi?cmd=connector%282%2C4%2C+silkm
>> ark%3Dnone%2Ceshift%3Dx%2Cetrunc%3D1%29&diamond=1
>>
>> alternate pin numbering (by swapping directions):
>>
>> http://igor2.repo.hu/cgi-bin/pcblib-param.cgi?cmd=connector%284%2C2%2C+silkm
>> ark%3Dnone%2Ceshift%3Dy%2Cetrunc%3D1%29&diamond=1
>>
>> Also figured the preview was mirrored compared to PCB's
>> coordinate-system, fixed that too.
>>
>> Regards,
>>
>> Igor2
>
>
> Please add more pin numbering options to connector generator. The existing one
> can be named "d-sub" style, also "flat cable" and "dip" should be considered.

Two alternate numbering can be achieved by pivoting n and m:

connector(2,3) and connector(3,2) will generate the same geometry 90 
degrees rotated but because of the pivot the numbering scheme (seems) 
different.

The "dip" numbering is not accessible this way, I will invent a parameter 
for that, thanks for the idea!

Regards,

Igor2