X-Authentication-Warning: delorie.com: mail set sender to geda-user-bounces using -f X-Recipient: geda-user AT delorie DOT com Date: Tue, 14 Jan 2014 10:14:13 +0100 From: Jan Kasprzak To: geda-user AT delorie DOT com Subject: Re: [geda-user] Side-mounted header connector Message-ID: <20140114091413.GH18632@fi.muni.cz> References: <20140114072906 DOT GE18632 AT fi DOT muni DOT cz> <20140114080501 DOT 5CE2E8045B75 AT turkos DOT aspodata DOT se> MIME-Version: 1.0 Content-Type: multipart/mixed; boundary="tT3UgwmDxwvOMqfu" Content-Disposition: inline In-Reply-To: <20140114080501.5CE2E8045B75@turkos.aspodata.se> User-Agent: Mutt/1.5.20 (2009-12-10) X-Muni-Spam-TestIP: 147.251.48.3 X-Greylist: Sender IP whitelisted, not delayed by milter-greylist-4.3.7 (tirith.ics.muni.cz [147.251.4.35]); Tue, 14 Jan 2014 10:14:15 +0100 (CET) X-Virus-Scanned: clamav-milter 0.97.8 at tirith.ics.muni.cz X-Virus-Status: Clean Reply-To: geda-user AT delorie DOT com Errors-To: nobody AT delorie DOT com X-Mailing-List: geda-user AT delorie DOT com X-Unsubscribes-To: listserv AT delorie DOT com Precedence: bulk --tT3UgwmDxwvOMqfu Content-Type: text/plain; charset=us-ascii Content-Disposition: inline karl AT aspodata DOT se wrote: : Yenya: : > I would like to use a 2x3 pin, 2.54mm spaced header connector for in-system : > programming of the MCU, but I am pretty restricted in the vertical direction. : > So I considered a side-mounted connector: one row of pins on the top side : > of the PCB, and another row on the bottom side, similar to the header : > on the right side of the following image: : > : > http://fabiobaltieri.files.wordpress.com/2011/08/usbasp.jpg?w=630 : > : > Is it possible to describe it with a single footprint? : : Yes, use a pad on each side like in : : http://turkos.aspodata.se/git/openhw/share/pcb/_connector/wascator_edge_3.fp : : Pad[ 10mm -3mm 10mm 3mm 2.0mm 0.5mm 0.2mm "1" "1" "square" ] : Pad[ 10mm -3mm 10mm 3mm 2.0mm 0.5mm 0.2mm "1" "1" "square,onsolder" ] : That's it, thanks! FWIW, here is the 2x3 edge-mounted header, I will also add it to gedasymbols.org. BTW, is there any way to make also silk layer lines "onsolder"? Thanks, -Yenya -- | Jan "Yenya" Kasprzak | | New GPG 4096R/A45477D5 - see http://www.fi.muni.cz/~kas/pgp-rollover.txt | | http://www.fi.muni.cz/~kas/ Journal: http://www.fi.muni.cz/~kas/blog/ | Please don't top post and in particular don't attach entire digests to your mail or we'll all soon be using bittorrent to read the list. --Alan Cox --tT3UgwmDxwvOMqfu Content-Type: text/plain; charset=us-ascii Content-Disposition: attachment; filename="header3_2_edge.fp" Element["Header 3x2, 2.54mm, edge-mounted" "header3_2_edge" "X?" "" 0 0 -12500 5000 0 100 ""] ( Pad[ 0 -7500 0 7500 5000 2000 6000 "1" "1" "square" ] Pad[ 0 -7500 0 7500 5000 2000 6000 "2" "2" "square,onsolder" ] Pad[ 10000 -7500 10000 7500 5000 2000 6000 "3" "3" "square" ] Pad[ 10000 -7500 10000 7500 5000 2000 6000 "4" "4" "square,onsolder" ] Pad[ 20000 -7500 20000 7500 5000 2000 6000 "5" "5" "square" ] Pad[ 20000 -7500 20000 7500 5000 2000 6000 "6" "6" "square,onsolder" ] ElementLine[ -5000 -8500 -5000 11000 1000 ] ElementLine[ 25000 -8500 25000 11000 1000 ] ElementLine[ -5000 11000 25000 11000 1000 ] ElementLine[ -3750 0 -5000 0 1000 ] ElementLine[ -3750 0 -3750 11000 1000 ] Attribute("author" "Jan Yenya Kasprzak, http://www.fi.muni.cz/~kas/") Attribute("copyright" "Jan Yenya Kasprzak, http://www.fi.muni.cz/~kas/") Attribute("use-license" "Unlimited") Attribute("dist-license" "GPL 2.0") Attribute("comment" "Thanks: Karl Hammar") ) --tT3UgwmDxwvOMqfu--