X-Authentication-Warning: delorie.com: mail set sender to geda-user-bounces using -f
X-Recipient: geda-user AT delorie DOT com
DKIM-Signature: v=1; a=rsa-sha256; c=relaxed/relaxed;
        d=gmail.com; s=gamma;
        h=mime-version:in-reply-to:references:from:date:message-id:subject:to
         :content-type:content-transfer-encoding;
        bh=5NBRmWvQeogkKlTSaVCKOcCs12fvCmpsOCV0GhVfsyU=;
        b=ZTpyHGsnsZWqiX1FGdHRMb6i+omYWC0CueR3QfSVjUTrcKsJgkauNFAUF79jNyXAmf
         ZlZYL42c5r3y/Uuf8xO4cYqJYtbq3DvGOblRuZqxTKMdixYXq3I8SLGcipaNhIPZhF09
         F0xWm+52S8op9JrwR77XWp20XDkzOtyb5hNks=
MIME-Version: 1.0
In-Reply-To: <4EDED68C.90607@optonline.net>
References: <4EDED68C DOT 90607 AT optonline DOT net>
From: Justyn Butler <justynbutler AT gmail DOT com>
Date: Wed, 7 Dec 2011 14:57:42 +0000
Message-ID: <CAHu0Z0WPdPno8A0Vo3pTOm77FdP+ncDcsy6Z=cp+8aPOz64rpA@mail.gmail.com>
Subject: Re: [geda-user] pcb gerbers not correct
To: geda-user AT delorie DOT com
Content-Type: text/plain; charset=ISO-8859-1
Content-Transfer-Encoding: 8bit
X-MIME-Autoconverted: from quoted-printable to 8bit by delorie.com id pB7FNThQ006520
Reply-To: geda-user AT delorie DOT com
Errors-To: nobody AT delorie DOT com
X-Mailing-List: geda-user AT delorie DOT com
X-Unsubscribes-To: listserv AT delorie DOT com
Precedence: bulk

I'm seeing exactly the same problem.

I have a 550mm x 18mm board that was created using gsch2pcb 1.6.2 and
routed with pcb 20110918.
When exporting the gerbers, the plated drill layer is significantly
misplaced, the rest of the layers look fine (although I've not double
checked that).

Exporting the same board from 20100929 produces no problems.

I am also on a 32-bit system.


On 7 December 2011 02:59, gene glick <geneglick AT optonline DOT net> wrote:
> I have a fairly large board, about 11"x11" - not sure if that is important
> or not, just throwing out the info.  It was routed using PCB Version 2010.
>  Generating gerbers from that version works just fine.  If I switch to 2011
> version, the gerbers come out wrong.  Specifically, the cnc plated drill
> file is moved way off from where it should be and has stuff moved where it
> should not be.
>
> Question is, is this just a version mismatch (route in 2010, gerbers in
> 2011)?  Actually, I just saved the file (save-as, with a new name) while
> running 2011.  The gerbers are  still really wrong.
>
> FYI, I routed a smaller board in 2011.  The gerbers look correct.
>
> gene