X-Authentication-Warning: delorie.com: mail set sender to geda-user-bounces using -f
X-Recipient: geda-user AT delorie DOT com
DKIM-Signature: v=1; a=rsa-sha256; c=relaxed/relaxed;
        d=gmail.com; s=20120113;
        h=mime-version:in-reply-to:references:date:message-id:subject:from:to
         :content-type;
        bh=PEYBgnJLmxJ17CyTtZjPJqQdmHE2Wb+c1u/Kb26Ttz0=;
        b=LDh+OdPMvXT8qHqAj/dpjV8wcfYdDr3e0qKbDa7vUFJjAD3lNIndKzbIdH/Hu9wEan
         QU0Bp2QAJGcjUvICI2jKi9h2IJZWEn82nRRy10SOPB2c0ydaC+TG7LBkp33cpCdFYFtO
         fL7Eu/c8TVLjkASfyh4SF0J6xwtlRqu3q0rgFedPLTccq8UOIOzgld04JFAjDHYahaGt
         2sIR5Iv1dE9fF7BhKJtdle2qlanNGULwYv68Sf5MZxSpiYZCcXHdTIVaYhxkXIBmGgGZ
         AxOXuiNOjjwIpo9/mqFNk04QJFnG9/8VG5tNI+IuJBQiKHL+2SIZtIIgRiprA+IPz/Or
         Db4g==
MIME-Version: 1.0
X-Received: by 10.221.74.81 with SMTP id yv17mr27235478vcb.15.1418858187478;
 Wed, 17 Dec 2014 15:16:27 -0800 (PST)
In-Reply-To: <201412172013.sBHKDAAx022528@envy.delorie.com>
References: <CALSZ9gqo83ZDuxZAYLaHp0=uXZvfe_1OougO9e4B6W9M86d3JA AT mail DOT gmail DOT com>
	<201412172013 DOT sBHKDAAx022528 AT envy DOT delorie DOT com>
Date: Wed, 17 Dec 2014 18:16:27 -0500
Message-ID: <CALSZ9gqUCPACc93Dm7Spotji=xGhT6962vJ9h=7AZJSccHKFRw@mail.gmail.com>
Subject: Re: [geda-user] Nema 23 stepper motors
From: Rob Butts <r DOT butts2 AT gmail DOT com>
To: geda-user AT delorie DOT com
Content-Type: multipart/alternative; boundary=001a11364314405d73050a71aa1f
Reply-To: geda-user AT delorie DOT com
Errors-To: nobody AT delorie DOT com
X-Mailing-List: geda-user AT delorie DOT com
X-Unsubscribes-To: listserv AT delorie DOT com
Precedence: bulk

--001a11364314405d73050a71aa1f
Content-Type: text/plain; charset=UTF-8

That might be it but I'll try micro-stepping first

On Wed, Dec 17, 2014 at 3:13 PM, DJ Delorie <dj AT delorie DOT com> wrote:
>
>
> Not sure if this is your problem, but on my lathe I need to *not* mesh
> the gears completely together to make them run smoothly.  If the gears
> press too much, the tip of one tooth hits the gullet of the opposite
> gear, causing noise.  Only the sides of the teeth should touch.  I use
> a piece of heavy paper between the lathe gears to separate them
> "enough".
>

--001a11364314405d73050a71aa1f
Content-Type: text/html; charset=UTF-8
Content-Transfer-Encoding: quoted-printable

<div dir=3D"ltr">That might be it but I&#39;ll try micro-stepping first<br>=
</div><div class=3D"gmail_extra"><br><div class=3D"gmail_quote">On Wed, Dec=
 17, 2014 at 3:13 PM, DJ Delorie <span dir=3D"ltr">&lt;<a href=3D"mailto:dj=
@delorie.com" target=3D"_blank">dj AT delorie DOT com</a>&gt;</span> wrote:<blockq=
uote class=3D"gmail_quote" style=3D"margin:0 0 0 .8ex;border-left:1px #ccc =
solid;padding-left:1ex"><br>
Not sure if this is your problem, but on my lathe I need to *not* mesh<br>
the gears completely together to make them run smoothly.=C2=A0 If the gears=
<br>
press too much, the tip of one tooth hits the gullet of the opposite<br>
gear, causing noise.=C2=A0 Only the sides of the teeth should touch.=C2=A0 =
I use<br>
a piece of heavy paper between the lathe gears to separate them<br>
&quot;enough&quot;.<br>
</blockquote></div></div>

--001a11364314405d73050a71aa1f--